Exabyte MAGNUM 1X7 LTO AUTOLOADER Manual Pagina 114
- Pagina / 162
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
98
PRODUCT MANUAL 1012581
CHAPTER 7—MAINTENANCE
3.
3.3.
3. Install the tape drive—With the tape drive right side up, slide it into the
autoloader as far as it will go without force.
Half height tape drive—Install in opening. Do NOT remove air block
plate.
Full height tape drive—Install as shown.
4.
4.4.
4. Connect the cables—Follow these steps to connect the cables.
a.
a.a.
a. Connect the serial cable to the tape drive (see Figure 7-2). The connector
is keyed to ensure the proper orientation.
b.
b.b.
b. Connect the SCSI cable and power cable to the tape drive. The connectors
are keyed to ensure the proper orientation.
c.
c.c.
c. Route the cables so that they don’t hang below the bottom edge of the
tape drive (see Figure 7-2).
!
! !
! Important
You must replace the installed tape drive with the same
configuration tape drive. You cannot replace a full height tape
drive with a half height tape drive, or vice versa.
Figure 7-10 Half height tape drive installation
Figure 7-11 Full height tape drive installation
Air block plate–
do NOT remove
Caution
Before connecting the SCSI cable in the following step, make sure that none of the
pins in the connector are bent.
- PRODUCT MANUAL 1
- ONTACTING 3
- Contents 5
- Product Overview 9
- Installing the Autoloader 9
- Configuring the Autoloader 9
- Autoloader Operation 10
- Maintenance 10
- Shipping the Autoloader 10
- ABOUT THIS MANUAL 13
- RELATED PUBLICATIONS 14
- PRODUCT OVERVIEW 17
- AUTOLOADER COMPONENTS 18
- BACK PANEL COMPONENTS 19
- INTERNAL COMPONENTS 20
- UTOLOADER COMPONENTS 21
- CHAPTER 1—PRODUCT OVERVIEW 22
- INSTALLING THE AUTOLOADER 23
- Remove this label 24
- Shipping 24
- Advertencia 27
- ASSEMBLING THE RAILS 28
- Insert screw here 31
- SCSI connectors 33
- SCSI terminator 34
- Ethernet port 34
- Power cord connection 35
- Power switch 35
- CONFIGURING THE 37
- AUTOLOADER 37
- Viewing the Home Screen 38
- Up a Level 39
- Next Choice 39
- Previous Choice 39
- Down a Level 39
- OVERVIEW OF AUTOLOADER MENUS 40
- Home Screen 41
- SETTING CONFIGURATION OPTIONS 42
- CHANGING THE LCD LANGUAGE 43
- CHANGING THE LCD CONTRAST 44
- CHANGING THE SCSI IDS 45
- Tape Drive SCSI ID 46
- CHANGING THE EMULATION MODE 47
- Enabling the Autoclean Option 50
- ETTING CONFIGURATION OPTIONS 51
- C h a n g e I P A d d r ? 52
- D H C P I s O N 52
- C h a n g e a 52
- C o n f i g u r a t i o n 52
- E n t e r P a s s w o r d 58
- Important 60
- CHECKING THE SETUP 61
- USING THE REMOTE 63
- MANAGEMENT UTILITY 63
- LIBRARY INFORMATION 65
- LIBRARY STATUS 66
- TAPE DRIVE STATUS 67
- INVENTORY 67
- CHANGE LIBRARY CONFIGURATION 71
- CHANGE ETHERNET CONFIGURATION 72
- CHANGE WEB ACCESS PASSWORD 74
- RUNNING DIAGNOSTICS 75
- 76
- AUTOLOADER OPERATION 77
- Cartridge 78
- PREPARING CARTRIDGES 79
- HAPTER 5—AUTOLOADER OPERATION 80
- Access hole for operating the 83
- L o a d D r i v e 84
- CLEANING THE TAPE DRIVE 86
- L T O 1 x 7 2 U 87
- D : N e e d s C l e a n i n g 87
- RESETTING THE AUTOLOADER 90
- RUNNING SYSTEM DEMOS 91
- PERFORMING DIAGNOSTIC TESTS 93
- STORING CARTRIDGES 94
- VIEWING AUTOLOADER 95
- INFORMATION 95
- RODUCT MANUAL 1012581 100
- C e l l # n B a r c o d e 103
- S e l e c t a C o m m a n d 103
- VIEWING CELL STATISTICS 104
- IEWING CELL STATISTICS 105
- VIEWING THE EVENT LOG 106
- MAINTENANCE 107
- PREPARING FOR REPLACEMENT 108
- REMOVING THE TAPE DRIVE 109
- Serial cable 110
- SCSI cable 110
- Power cable 110
- ! Important 111
- Unload button 112
- EPLACING THE TAPE DRIVE 113
- Air block plate– 114
- CLEANING THE AUTOLOADER 115
- PRODUCT MANUAL 1012581 116
- TROUBLESHOOTING 119
- SCSI BUS INFORMATION 126
- OPERATING SYSTEM INFORMATION 127
- DIAGNOSTIC INFORMATION 127
- ADVANCED TROUBLESHOOTING 128
- SHIPPING THE AUTOLOADER 129
- Remove this screw 130
- (one each side) 130
- Insert shipping key here 131
- Foam spacers 133
- SPECIFICATIONS 135
- PERFORMANCE SPECIFICATIONS 136
- CARTRIDGE INVENTORY TIMES 137
- MOVE COMPLETE TIME 137
- RELIABILITY 137
- POWER SPECIFICATIONS 138
- ENVIRONMENTAL SPECIFICATIONS 139
- ACOUSTIC NOISE LIMITS 140
- SHOCK AND VIBRATION LIMITS 140
- SHIPPING SPECIFICATIONS 141
- CANADIAN VERIFICATION 142
- EUROPEAN COMMUNITY 142
- USTRALIA AND NEW ZEALAND 143
- APPENDIX A—SPECIFICATIONS 144
- WRITE ONCE, READ MANY 145
- (WORM) CAPABILITY 145
- DATA SECURITY ON WORM MEDIA 146
- WORM MEDIA ERRORS 146
- REQUIREMENTS 147
- TAPEALERT FLAGS 147
- ERROR CODES 148
- ERROR MESSAGES 149
- APE ALERT FLAGS 151
- APPENDIX C—ERROR MESSAGES 154
- PRODUCT LIMITED WARRANTY 161
- ON SITE SERVICE (OSS) 161
- WARRANTY 162
Relacionado con productos y manuales para Las unidades de cinta Exabyte MAGNUM 1X7 LTO AUTOLOADER
(6 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.107 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales